Elevador De Voltaje, Electronica, Robotica, Sensores
Elevador De Voltaje, Electronica, Robotica, Sensores a
12 meses de $ 24,00
Garantia contra defectos de fabricacion
SANDOROBOTICS TRAE PARA TI:
ELEVADOR DE VOLTAJE Pololu Adjustable Boost Regulator 2.5-9.5VThis powerful, adjustable boost regulator can generate an output voltage as high as 9.5 V from an input voltage as low as 1.5 V, all in a tiny, 0.42" x 0.88" x 0.23" package. A trimmer potentiometer lets you set the boost regulator’s output voltage to a value between 2.5 and 9.5 V.OverviewThe Pololu adjustable boost regulator is a very flexible switching regulator (also called a switched-mode power supply, SMPS, or DC-to-DC converter) that can generate voltages higher than its input voltage. We offer two adjustable ranges: approximately 2.5 V to 9.5 V and 4 V to 25 V. The output voltage can be set using the trimmer potentiometer in the upper-right corner of the board. The input voltage range is 1.5 V to 16 V (the input voltage should be kept below the output voltage).
Some example applications include:Powering 5 V or 3.3 V systems from lower-voltage batteries.Powering 5 V subsystems (e.g. sensors) in lower-voltage (e.g. 3.3 V) systems.Achieving consistent actuator operation when powered by fluctuating batteriesPowering high-brightness LEDs or a large number of LEDs in seriesFeature summaryinput voltage: 1.5 V to 16 Voutput adjustable from 2.5 V to 9.5 V or 4 V to 25 V750 kHz switching frequency2 A switch (and input) limitintegrated over-temperature and over-current shutofftypical efficiency of 80-90% when doubling voltage and with 100-500 mA outputsmall size: 10.7 x 22.4 x 5.8 mm (0.42" x 0.88" x 0.23")weight without header pins: 1.6 g (0.06 oz)Using the Boost RegulatorConnectionsThe boost regulator has just three connections: the input voltage, ground, and the output voltage. These three connections are labeled on the back side of the PCB, and they are arranged with a 0.1" spacing along the edge of the board for compatibility with standard solderless breadboards and perfboards and connectors that use a 0.1" grid. You can solder wires directly to the board or solder in either the 3×1 straight male header strip or the 3×1 right-angle male header strip that is included.Setting the output voltageThe output voltage can be adjusted using a meter and a light load (e.g. a 1k resistor). Turning the potentiometer clockwise increases the output voltage. The output voltage can be affected by a screwdriver touching the potentiometer, so the output measurement should be done with nothing touching the potentiometer. The potentiometer has no physical end stops, which means that the wiper can be turned 360 degrees and into an invalid region in which the output voltage is set to approximately 2.5 V (for both the 2.5 V to 9.5 V and 4 V to 25 V versions). The input voltage should not exceed the output voltage, so we recommend setting the output voltage with the input voltage set to around 2.5 V.Output voltage settings for the adjustable boost regulators.The absolute limit for the input voltage is double the output set voltage. For example, if the output is set to 6 V, the input must not exceed 12 V. Once the input exceeds the output set point, the output voltage will rise with the input voltage since the input is connected to the output through an inductor and a diode.Note: The trimmer potentiometer is not rated for continual adjustment back and forth; the intended application is to set the output voltage a few times in its life.Efficiency and available output currentThe available output current depends on the input and output voltages. The input current is limited to approximately 2 A, and, as shown in the graphs below, the efficiency is typically 80% to 90%. Therefore, the maximum available current will be approximately 800 mA when doubling the input voltage and approximately 400 mA when quadrupling the input voltage. At high output powers, the 20% lost in the regulator will cause substantial heating, which can limit the available output power (the regulator will automatically shut off if its internal temperature gets too high). At low output currents and high input and output voltages, the efficiency drops closer to 50%, though the lower power involved prevents heating from being an issue. Some output voltages shown in the efficiency graphs below can only be achieved using the 4-25V adjustable boost regulator.
Si pagas a nuestras cuentas antes de las 2 de la tarde las cuales mandamos a tu correo en cuanto ofertes se manda el mismo dia. En caso de pagar por mercado pago, se MANDARA, en cuanto se reciba el correo de mercado libre que ya acreditaron su pago esto tarda de 1-2 dias en que nos avisen aunque se haya pagado el envío mas caro.
ANTES DE PAGAR A CUALQUIER MEDIO NECESITAMOS TENER TU CODIGO POSTAL Y ESTADO PARA PODERTE COTIZAR EL ENVIO YA QUE SI PAGAS EL MAS BARATO A VECES REDPACK NO LLEGA A TODAS LAS COMUNIDADES Y NO SE PODRA ENVIAR.
ANTES DE OFERTAR RESUELVE TODAS TUS DUDAS EN LA SECCION PREGUNTAS Y RESPUESTAS, ESTAMOS PARA SERVIRTE. UNA VEZ QUE OFERTES TIENES SOLO 3 DIAS PARA CONCRETAR LA VENTA SI NO SE CALIFICARA NEGATIVAMENTE SIN NINGUN AVISO!
- Valoraciones (0)